Rough-country 370.20 User Manual

Browse online or download User Manual for For the car Rough-country 370.20. Rough Country 370.20 User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 4
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
94-01 3” 1500 DODGE SUSPENSION LIFT KIT
92756600R1
Kit Contents:
9281:Front Coil Springs
7566:
Upper Control Arms
Lower Control Arms
Sway bar Brackets
6522:
2” Blocks
U-bolt
8157: Front Shock
8158: Rear Shock
Tools Needed:
Torque Wrenches
½” Drive Rachet and Sockets
Assorted Combination Wrenches
Heavy Duty Jack Stands
Hydraulic Floor Jacks
Channel Locks
Drill
13/32” Bit
Hammers
C-Clamps
Center Punch
Rubbing Alcohol
Safety Glasses
Anti-Seize Compound
Thank you for choosing Rough Country for your suspension needs.
Rough Country recommends a certified technician installs this system. In addition to these instructions, professional
knowledge of disassemble/reassembly procedures as well as post installation checks must be known. Attempts to install
this system without this knowledge and expertise may jeopardize the integrity and/or operating safety of the vehicle.
Please read all the instructions before beginning the installation. Check the kit hardware against the parts list. Be sure
you have all the needed parts and understand where they go. Also please review the tools needed list and make sure
you have needed tools.
PRODUCT USE INFORMATION
As a general rule, the taller a vehicle is the easier it will roll. We strongly recommend, because of rollover possibility, that
seat belts and shoulder harnesses should be worn at all times. Avoid situations where a side rollover may occur.
Braking performance and capabilities are decreased when significantly larger/heaver tires and wheels are used. Take
this into consideration while driving. Also, speedometer recalibration is necessary when larger tires are installed.
Do not add, alter, or fabricate any factory or after-market parts which increase vehicle height over the intended height of
the Rough Country product purchased. Mixing component brands, lifts, and/or combining body lift with suspension lifts
voids all warranties. Rough Country makes no claims regarding lifting devices and excludes any and all implied claims.
We will not be responsible for any product that is altered.
This kit is packaged as a leveling kit—raising the front 3” and the back 2”. If you desire a different look or if your truck
has a tool box or added weight in the rear please consult with your sales repetitive about option higher block and u-bolt
options or the use of an add-a-leaf.
The 3” suspension system was developed for 33x12.50x15 tire on an after market wheel with 5” of back spacing.
NOTICE TO DEALER AND VECHICLE OWNER
Any vehicle equipped with any Rough country product must have the “Warning to Driver” decal installed on the sun visor
or dash. The decal is to act as a constant reminder for whoever is operating the vehicle of its unique handling character-
istics. INSTALLING DEALER—It is your responsibility to install the warning decal and to forward these installation in-
structions on too the vehicle owner for review and to be kept in the vehicle for its service life.
Torque Specs:
Size Grade 5 Grade 8
5/16” 15 ft/lbs 20 ft/lbs
3/8” 30 ft/lbs 35 ft/lbs
7/16” 45 ft/lbs 60 ft/lbs
1/2” 65 ft/lbs 90 ft/lbs
9/16” 95 ft/lbs 130 ft/lbs
5/8” 135 ft/lbs 175 ft/lbs
3/4” 185 ft/lbs 280 ft/lbs
Class 8.8 Class 10.9
6MM 5 ft/lbs 9 ft/lbs
8MM 18ft/lbs 23 ft/lbs
10MM 32ft/lbs 45ft/lbs
12MM 55ft/lbs 75ft/lbs
14MM 85ft/lbs 120ft/lbs
16MM 130ft/lbs 165ft/lbs
18MM 170ft/lbs 240ft/lbs
Page view 0
1 2 3 4

Summary of Contents

Page 1

94-01 3” 1500 DODGE SUSPENSION LIFT KIT 92756600R1 Kit Contents: 9281:Front Coil Springs 7566: Upper Control Arms Lower Control Arms Sway b

Page 2 - See Photo 3

9. Attach the grease fittings provided with the new Rough Country lower suspension arms using a 3/8" wrench. Note: install two 90º grease fittin

Page 3 - Photo 8

11. Remove the upper suspension arm nut and bolt at the axle a shown in Photo 6. Remove the nut and bolt at the frame and remove the upper suspension

Page 4

REAR INSTALLTION 1. Chock front wheels and jack up the rear of the vehicle. Secure with jack stands on the frame rail. 2. Place a floor jack under

Comments to this Manuals

No comments