Rough-country RC701 User Manual

Browse online or download User Manual for For the car Rough-country RC701. Rough Country RC701 User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 12
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
07-11 GM 4WD 1500 P/U 1 1/4” Body Lift
Thank you for choosing Rough Country for all your suspension needs.
Rough Country recommends a certified technician install this kit. Attempts to install this kit without this knowledge and
expertise may jeopardize the integrity and/or operating safety of the vehicle.
Please read instructions before beginning
installation. Check the kit hardware against the kit contents list page. Be sure you have all needed parts and know
where they go. Review tools needed list and make sure you have the tools needed to install the kit.
PRODUCT USE INFORMATION
We will not be responsible for any product that is altered. We will be happy to answer any questions concerning the de-
sign, function, and use of our products by calling 800-222-7023.
Kit was designed for use with both standard cab and 4 door models. Standard cabs will not utilize all cab mount
spacers. Standard cabs only will use the cab strap extension brackets.
This body lift was developed using a 33x12.5x20 tire with factory wheels. Combo kits are available. Ask your
Rough Country Dealer for more info.
NOTICE TO DEALER AND VEHICLE OWNER
Any vehicle equipped with any Rough Country product should have a “Warning to Driver” decal installed on the inside of
the windshield or on the vehicle’s dash. The decal should act as a constant reminder of the vehicles unique handling
characteristics. These instructions should be kept in the vehicle for its service life.
92RC70100
Kit Contents:
2-Fr Bumper Outer Relocation Brackets
2-Fr Bumper Frame Brackets
8-1 1/4” X 3” Cab Spacers
8-1 1/4” X 2” Bed Spacers
2-Standard Cab Strap Ext.
RC701BAG Containing:
For Front Cab Mounts:
14mmx 140mm Bolts (6)
12mm x 140mm Bolts (2)
For Front Bumper Brackets:
3/8” x 1” Bolts (4)
3/8” Flat Washers (4)
3/8” Lock Nuts (4)
For Bed Mounts:
12mm x 65mm Bolt (6)
For Rear Bumper:
10MM Nut (2)
1-1/4” Tall X 2’ 9/16” ID Pucks (2)
1” Tall X 2” Body Pucks (2)
14mm x 60mm Bolts (4)
For Ground Wire Extension:
1/4” x 3/4” Bolt (1)
1/4” Flat Washer (2)
1/4” Lock Nut (1)
For Strap Extension:
12mm x 35mm Bolts (2)
12mm Flange Lock (2)
1/2” Flat Washer (2)
Tools Needed:
Jack
Jack Stands
Wood Blocks (2x4)
Pliers
Hammer
Phillips Screwdriver
Drill Motor
1/2” Drill Bit
Reciprocating Saw
Clamp
8mm Socket
10mm Socket / Wrench
14mm Socket / Wrench
13mm Socket / Wrench
15mm Socket / Wrench
16mm Socket / Wrench
18mm Socket / Wrench
19mm Socket / Wrench
21mm Socket / Wrench
22mm Socket / Wrench
Hand Grinder
Page view 0
1 2 3 4 5 6 ... 11 12

Summary of Contents

Page 1

07-11 GM 4WD 1500 P/U 1 1/4” Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified techn

Page 2

8. With bumper still removed, use the supplied template to mark and drill the new holes in the frame. See Photo 13. 9. Drill the holes using a 1/2”

Page 3

PHOTO 19 INSTALL THE 14MM X 60MM BOLTS POST INSTALLATION INSTRUCTIONS 1. Check all fasteners for proper torque. Check to ensure for adequate cleara

Page 4

REAR BUMPER DRILLING TEMPLATE

Page 5

CAB INSTALLATION INSTRUCTIONS 1. Raise hood disconnect positive and negative battery cable from the battery using 10mm wrench. This is done to preve

Page 6

10. Remove upper radiator hose and overflow hose from fan shroud as shown in Photo 7 & 8. 11. Disconnect air intake hose from air box using a Phil

Page 7

LOOSEN FRAME END OF STRAP 15. Disconnect the emergency brake cable at the connection on the frame below the drivers door by removing the front part of

Page 8

19. Lift only enough to place body puck on top of body mount. See Photo 19. Note: Passenger side front body mount bolt can be removed by lifting the b

Page 9

31. Find the tab on driver side body mount where the emergency brake cable runs beside it and bend it up flat with frame to gain slack for cable. See

Page 10

38. Install tow hooks so that they are upside down and install stock bolts. Tighten to 65ft-lbs using a 18mm wrench / socket. See Photo 31. 39. Insta

Page 11

1. Unplug the license plate light connector and if equipped the trailer wiring connector. See Photo 1 & 2. 2. Remove the 3 bolts from the driver

Page 12

5. Loosen the six bed bolts using 18mm socket but only remove one side at a time. See Photo 6, 7 & 8. 6. With jack stand or hydraulic jack and w

Comments to this Manuals

No comments